unit: mm intelligent power devices (ipds) MIP508 silicon mos ic features 3-pin intelligent power device five protective functions (over-current, over-voltage, short circuit load, over heat, esd) are integrated acceptable both ac and dc power supply applications for lamp and solenoid drive 1 : in 2: drain 3: source minip3-f1 package block diagram gate cut-off circuit esd protection over current protection over voltage protection s in d short circuit load protection over heat protection 4.5 0.1 3.0 0.15 45 2.6 0.1 0.4 max. 1.6 0.2 1.5 0.1 4.0 2.5 0.1 3 +0.25 0.20 1.0 +0.1 0.2 0.5 0.08 0.4 0.04 0.4 0.08 12 3 1.5 0.1 3 absolute maximum ratings (ta = 25c) parameter output voltage output peak current output current input voltage input current drain clamp energy allowable power dissipation channel temperature storage temperature t c = 25c t c = 85c t c = 25c ta = 25c ta = 85c symbol v ds i op i o v in i in e clp p d t ch t stg ratings 40 3 1 1 ? 0.5 to 6 5 24 * 1 2 1 * 2 0.52 * 2 ? 40 to +150 ? 55 to +150 unit v a a v ma mj w c c * 1 l = 10mh, v dd = 20v, i l = 2.19a, t c = 25c, 1pulse * 2 mounting on the pcb (the copper foil of the drain portion should have a area of 100mm 2 or more and the board thickness should be 1.7mm.) 1 slb00020a ed publication date: august 2002
MIP508 electrical characteristics (t c = 25 3c) parameter drain to source on-resistance drain to source on-voltage drain clamp voltage drain off current (1) drain off current (2) input voltage (high) input voltage (low) input current over current protection limit short circuit load protection limit symbol r ds(on) v ds(on) v ds(clp) i ds(off)1 i ds(off)2 v in(h) v in(l) i in(on) i ocp v ds(sht) conditions v in = 5v, i ds = 1a v in = 5v, i ds = 1a v in = 0, i ds = 3ma v in = 0, v ds = 12v v in = 0, v ds = 16v i ds = 1a i ds = 1ma v in = 5v, v ds = 0 v in = 5v v in = 5v min 40 4 2 2 typ 0.5 0.5 49 50 70 0.15 3 4 max 1.1 1.1 58 120 180 0.8 0.5 10 unit v v a a v v ma a v note: the oscillation of the output current is caused when the drain voltage exceeds the short circuit load detection voltage u nder the on state of output. electrical characteristics (t c = 25 3c) parameter over heat protection temperature symbol t shd conditions v in = 5v min 160 typ 190 max unit c note 1: the above values of characteristics are not guaranteed values and are only references for designing. note 2: if the chip temperature exceeds the "over heat protection temperature", output current is shut down. timing chart v in v ds i ds latch cancel on state on state off state over current limiting state short circuit load state over heat protection operating state over heat latch detecting short circuit load detecting over heat 2 slb00020a ed
request for your special attention and precautions in using the technical information and semiconductors described in this material (1) an export permit needs to be obtained from the competent authorities of the japanese government if any of the products or technologies described in this material and controlled under the "foreign exchange and foreign trade law" is to be exported or taken out of japan. (2) the technical information described in this material is limited to showing representative characteris- tics and applied circuits examples of the products. it neither warrants non-infringement of intellec- tual property right or any other rights owned by our company or a third party, nor grants any license. (3) we are not liable for the infringement of rights owned by a third party arising out of the use of the product or technologies as described in this material. (4) the products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instru- ments and household appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (5) the products and product specifications described in this material are subject to change without notice for modification and/or improvement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (6) when designing your equipment, comply with the guaranteed values, in particular those of maxi- mum rating, the range of operating power supply voltage, and heat radiation characteristics. other- wise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) when using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) this material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of matsushita electric industrial co., ltd. 2002 jul
|
